MADS Electronics - SMARTY J67 for Dodge Ram 6.7L Cummins 2007.5 - 2010

MADS ELECTRONICS

KLM is proud to be a distributor of MADS Electronics products -- and in particular the Smarty power modules. Each performance enhancer in the Smarty line gives you the ability to choose several levels of increased power or reduced fuel consumption, according to your current driving needs.

KLM Performance offers FREE 2ND DAY SHIPPING on the SMARTY J67. The MADS Electronics Smarty-J67 is for the 2007.5 to 2009 Dodge Ram trucks powered with the 6.7L Cummins The SMARTY J67 is now loaded with the latest REVOLUTION Software and the the POD (Power On Demand) feature. The SMARTY J67 has two different software options available - The standard software and the ME software. The standard software is for a truck with a stock emissions system with the Diesel Particulate Filter (DPF) in place. The ME software assumes that you have an off-road exhaust system with the DPF removed. Both of these SMARTY J67 programs offer the following features.

Key features of the SMARTY J67 for the Dodge Cummins Turbo Diesel 6.7L

* 40 / 70 / 100 hp power levels
* Lowest EGT's in the industry
* Improved fuel economy
* Optimized drivability
* Fast ABS tire height updates from 22.5" to 44"
* Internet up-datable for latest software available
* Easy installation
* No tools necessary - no fuses to pull
* Fastest programming in the industry
* POD Software adds adjust-ability and the potential for even greater mileage gains
* Cold weather 3 Cylinder High Idle is enabled in all power levels
* USB port built in for simple updates from internet
* Reads Diagnostic Trouble Codes in plain text
* CaTCHER software's inside
* The rail pressure is Not Increased above the factory settings
* SMARTY J67 is designed for both MPG increases and Exhaust Gas Temperature reduction.

This SMARTY J-67 is geared toward the customer who wants reliable and safe power for both the engine and the transmission combined with good fuel mileage. One of the main design criteria of the MADS Electronics SMARTY J67 during the development of the performance software have been to lower the EGT's and provide the lowest smoke levels possible. When using the SMARTY J67 at the highest horsepower level the typical exhaust gas temperatures are on average 200 degrees F cooler than with stock software!
Faster than anything else on the market. Again, we've done our homework on the protocol. Depending upon the year of the truck, it takes from about three minutes to about five and a half. Three times faster than competitors.

Updates

If you have followed the Smarty for the VP trucks, then you've noticed that MADS has released several updates for it in a relatively short time. Well, you can expect the same to happen for the CR. The CaTCHER software modules as they are today are only a starting point.

NOTE: FEDEX requires a signature for the delivery of these packages. Please list a shipping address where someone can sign for the delivery.

MADS Electronics - Smarty Catcher FAQs

The MADS Electronics tuning software is well known as CaTCHER software. MADS Electronics original products were EPROMs and Flash-EPROMs (or “chips”) which could be installed in place of the original OEM EPROMs and Flash-EPROMs located in the vehicle’s on-board control module. These chips, just like the tuners of today, keep the entire vehicle safety and emissions systems intact, but modify the fuel injection settings to deliver dramatic power, torque and drivability improvements.

Also the fuel consumption is one of the most important point of MADS Electronics research. CaTCHER software can be used to reduce fuel consumption up to 15% depending on the driving condition.

With the advent of OBD-II vehicle control module in the early 1990s, most domestic vehicle manufacturers installed under-dash ports (“ALDL ports”) which allowed dealers and service techs to “re-flash” the vehicle's control module to change engine settings without replacing any chip.

So today, instead of chips, MADS Electronics products are hand-held tuners that achieve the same dramatic drivetrain improvements, without the hassle of popping the hood, pulling out the vehicle control module and replacing a chip. Installation is quick and easy, taking just 2 minutes and requiring no tools or mechanical skills whatsoever.

Q. What does "CaTCHER " stand for?

A.  CaTCHER stands for Clutch and Traction Challenger.

Q. What is so special about the CaTCHER?

A. The CaTCHER software is a unique animal.  It improves throttle response of the engine greatly.  It spools up the turbo sooner. (On average 200 RPM sooner.) It deals with the injection timing. It alters the torque management. Just to mention a few benefits. Customers report that the engine now "hangs" on the throttle.

Q. What has Smarty to do with the CaTCHER software?

A. Smarty is the tool  you need to update your ECM with any level of the CaTCHER software. There are ten different software packs in Smarty you can choose from.

Q. What's the difference in the CaTCHER software?

A. Mainly the throttle response, or maybe better the aggressiveness of the engine response. Since the full blown CaTCHER develops torque instantly, it can become a pain to drive it on slippery roads. Thus the need  to reduce the response some. Further more, there are CaTCHER versions with and without added timing stored in the Smarty. The software without added timing are useful if you want to use a timing box stacked with the CaTCHER.

Q. Does Smarty have only CaTCHER software on board?

A. No,  Smarty offers SW# 0 that provides about HALF the power of a stock software. Emissions. Ehm. SW# 1 is a Fuel Saver software. SW# 2 deals only with fuel and boost.  SW
# 3 is fuel, boost, and timing.  The remaining levels can be considered CaTCHERs.

Q. Does Smarty do the boost fooling function?

A. Yes, all the the software modules in Smarty have modified boost tables in them in order to allow for higher boost without defuelling. (Except SW#0 and of course stock)

Q. Could you take  Smarty and install it on several different trucks, one at a time?

A. Yes! No problem, when you go back to stock Smarty unlocks from the VIN# and ECM. Now you're ready to go into another truck. As many times as you want.

Q. Can Smarty go from one program to another, or do you have to go back to stock, then to a program?

A. You can go from any software # to any other software #. There is no need to go back to stock.

Q. Is Smarty ECM or VIN sensitive?

A. YES! Smarty only works with one truck AND one ECM at one time.

Q. What if a dealer flashes the ECM and Smarty was not returned to stock? Is my Smarty now useless?

A. We've been asked that question many times. Upon request, there is a "safety feature" in Smarty. Should a reflash happen without having Smarty returned to stock first, you need to contact us and tell us the  serial # of your Smarty and the VIN# of your truck.

With that information we can provide you with a password that will allow Smarty to update your ECM. That password will work ONLY ONE TIME. That means that you can unlock Smarty from the ECM only one time.

Q. Which version of "stock" will the Smarty come with.

Smarty does NOT download the complete original software from the ECM and does not store it into it's memory. That is for a simple reason. The protocol in the ECM does not allow to read the flash memory. How can Smarty then return to stock? Simple. It has all the latest stock software already on board. When you choose to return the truck back to stock, Smarty takes the stock software from it's memory and updates the ECM with that software.

Q. Is Smarty's  DTC reader also VIN# locked?

A. No, the DTC reader works always in any truck. Even when Smarty is VIN# locked to your truck, you can still diagnose your buddy's truck. MADS did not want you to have the hassle of going
back to stock only because you need to help someone.

Q. How long does it take to update the ECM with Smarty?

A. We've done some serious research in order to minimize the time needed for an update. We've developed special boot loaders which cut the required time for an update dramatically. A typical update is done in about two minutes with Smarty S-03A and three and a half minutes with Smarty S-06A. Once you get used to Smarty it takes a few minutes from the moment you plug in
Smarty to finish. With the fastest competition it takes more than twice that time.

Q.  Does the Smarty Mount in the truck... or program and then unplug?

Smarty needs to be plugged into the OBD port of your truck, program the ECM, then unplugged.

Q. If the update is interrupted, how can I recover the ECM?

First of all don't panic! An interrupted update is a piece of cake for Smarty. Smarty will recover your truck automatically back to the STOCK software. Unlike the competition, you don't have  to remove fuses or battery cables. Smarty will handle the situation on it's own. You just need to turn the key on, plug in Smarty and follow the on-screen instructions. A special boot loader does that job.

Q.  Can a dealer detect Smarty?

If you take your truck back to stock software then the answer is no. Smarty updates are NOT
detectable by the dealer!

Q.  Does the CaTCHER raise the rev limiter?

The CaTCHER versions alter the high RPM settings in the ECM for fuel, timing, boost, torque limiter whatever... in order to allow the engine to rev. Depending upon the mods done to the engine that shows up on a dyno graph or does not.

Q.  How much horsepower will the CaTCHER add to my 98.5-02 engine?

A. The CaTCHER is VERY noticeable from idle up. As soon as you touch the throttle, you will KNOW that the CaTCHER is in there. First of all, the power added by the CaTCHER depends upon the mods done to the engine. On a stock engine, typically we see an HP increase at the rear wheels of about 60 HP.

With taller injectors, the HP gain increases. How much? That depends upon the injectors, turbo, intake, and exhaust. The best mod combined with a CaTCHER is without doubt a good set of injectors.

Fuel pump wire tapping boxes without added timing come next if you're after serious HP. In that kind of scenario, the CaTCHER becomes very noticeable in the top HP range. Some customers have gained over 75 HP with that kind of stack above all other stacks they had tried before.

Is there a warranty on this product?

Of course! Anyway, let me mention the fact that out of the over 2000 Smarty's sold thus far, we have had only five defective units. MADS uses the strictest quality control possible. Every single unit is tested individually four different times during the assembly before it leaves our facility. Everything is traceable for every single unit. MADS knows exactly where the parts for it came from, who assembled it, who tested it. MADS wants the Smarty products to be as trouble free as possible.

What is the Warranty Period?

One year.